In ‘3D Printing a Microfluidic Chip Capable of Droplet Emulsion Using NinjaFlex Filament,’ Robert Andrews from the University of Arkansas 3D prints a novel microfluidic system for his thesis project and paper. Relying on NinjaFlex filament, the process is centered around droplet emulsion—and the BioMEMS (bio microelectromechanical systems) project.
Another main element in this project is the development of a lab on a chip, also delving into miniaturization (technology shrunken into a much smaller environment), with benefits like:
- Reduced necessary sample sizes
- Shortened reaction times of lab processes
- Greater mobility in lab processes
In the lab-on-a-chip scenario, the scale is around 10-1000 µm, but many of the common processes for making such an environment are time consuming and expensive—which is why 3D printing is such an attractive medium for miniaturization. Andrews points out the need for suitable fluid flow, which occurs with a pressure gradient or flexible diaphragm, and must be situated along the microfluidic channel.
“Depending on the material and the thickness of the diaphragm, varying pressures and frequencies would be needed to achieve a certain flow rate,” states Andrews. “As a side note, these diaphragms can also be used either to modify the width of the microchannel, or as check valves if the pressure is increased beyond a certain threshold (enough to cause the displacement of the diaphragm to be equal to the diameter of the microfluidic channel).”
In his thesis project, Andrews works to determine what limitations there may be on the printing process, along with designing the microchip. The microfluidic droplet separators would work within a host of applications, to include blood monitoring (for clots), food safety chemical detection, and discovery of new drugs in pharmaceuticals. The author also points out how beneficial it would be to create a system using NinjaFlex—in comparison to more conventional methods.
“3D printing in NinjaFlex rather than ABS has one inherent advantage for the specific application of generating microfluidic systems. NinjaFlex has a Young’s modulus of 12 MPa, while that of ABS is 2.05 GPa. This results in ABS having a stiffness roughly 170 times that of NinjaFlex,” Andrews wrote.
“This reduction in stiffness is advantageous for fabrication of microfluidic systems because these systems may need actuators that need to flex and bend to generate fluid flow. Much less pressure is needed to generate a deflection in NinjaFlex than to generate that same deflection in a geometrically similar sample of ABS.”
Through ‘trial and error,’ Andrews was able to find the best printing parameters for fabricating the chip. There were also some worries about the chip design, concerning major defects with blockage, and the first print was a bit rough, including:
- Print quality distortion
- Blocking of the outlet
- Chip is too thick
- No visibility of micro channels or diaphragm
“With respect to the 3D printer itself, it was noted that jams often occurred at this extruder temperature,” states the author. “Because of this, temperature was increased to 250 C. Jams occurred much less frequently, if at all, at this extruder temperature.
“With respect to design changes in the next iteration, the top of the chip was removed in the part file, leaving the channels viewable from above. Instead of a top composed of NinjaFlex, the microchip would be capped with a glass chip.”
The Angled Junction Version 3 chip was the first used with droplet emulsification, as water colored with green food dye was filtered through to ensure the channel was not blocked. The microchannel turned green, but Andrews points out that the bond between the filament and the glass was not very good. Water leaked from the chip—and it ended up separated from the substrate.
After continued refining, Andrews was able to bring the flow rate down, with the oil side pressure maintaining the same levels. Afterward, ‘consistently sized droplets’ were created at regular intervals.
“There are various ways that this final design of the microchip could be improved. First, the diameter of the channels could be decreased to reduce the size of the droplets. However, the channels cannot be made so small that they become blocked. Also, diaphragms could be implemented on either side of the outlet channel. By actuating these diaphragms, the microchannel size can be changed and, consequently, the size of the droplets could be accurately controlled. The chip could be made thicker to allow the tube connectors to have more surface to grab onto,” concluded Andrews.
“The overall design of the experiment could also be improved. Generating the oil flow rate would be better accomplished using a syringe pump rather than using the nitrogen tank as a pressure source. Since not much pressure is needed to pump the oil, the nitrogen tank is not accurate enough to produce a reliable and consistent oil flow rate.”
The future has arrived in many different forms of research and industrial innovation, but it may be different from what many of us imagined; for instance, miniaturization is becoming more common, from forays into flow channel miniaturization to continuous flow reactors, and different materials and processes for miniaturization and microfluidics. What do you think of this news? Let us know your thoughts! Join the discussion of this and other 3D printing topics at 3DPrintBoard.com.
[Source / Images: ‘3D Printing a Microfluidic Chip Capable of Droplet Emulsion Using NinjaFlex Filament’]
If you're in need of 3D interior and exterior design services in the USA, our platform offers a comprehensive solution to bring your architectural projects to life. Through our service, you can request detailed 3D renderings that showcase both the interior and exterior of your property. Whether you're designing a home, office, or commercial space, our experts deliver photorealistic visualizations that highlight every element, from furniture arrangements to building facades, ensuring that your vision is accurately represented.
Through our website, you can easily access 3D interior and exterior design services tailored to your specific needs. With our help, you'll be able to create stunning visual representations of your designs, allowing you to present them to clients, investors, or stakeholders in a professional and engaging manner. Our team focuses on bringing out the best in your designs, ensuring that both the interior spaces and exterior elements are rendered with the highest level of detail and realism.
